CSWA - Certified Solidworks Associate 2D Sketching and Relations Questions and Answers — Questions and Answers
Question 1: When sketching in SolidWorks, you notice that a sketch is displayed in red and yellow colors, and the status bar indicates 'Over Defined'. What is the most likely cause?
- The sketch is missing a critical dimension or relation.
- Conflicting or redundant dimensions and/or geometric relations have been applied. (Correct answer)
- The sketch contains construction geometry.
- The sketch entities have not been related to the origin.
Correct answer: Conflicting or redundant dimensions and/or geometric relations have been applied.
An 'Over Defined' sketch occurs when there are duplicate or conflicting dimensions and relations. This redundancy provides too much information, and SolidWorks cannot solve the sketch. The red and yellow colors are visual indicators of this conflict.
Question 2: In a 2D sketch, you need to ensure that a circle and a line touch at only a single point, without crossing. Which geometric relation should you apply between the two entities?
- Coincident
- Concentric
- Tangent (Correct answer)
- Midpoint
Correct answer: Tangent
The 'Tangent' relation is used to make two curved entities or a line and a curved entity touch at a single point without intersecting. A 'Coincident' relation would place the line on the circle's circumference, and 'Concentric' applies to two circles sharing a center point.
Question 3: What is the primary purpose of using 'Construction Geometry' (e.g., a centerline) in a SolidWorks sketch?
- To create solid features like extrusions or cuts.
- To serve as a reference for creating other sketch geometry, without being part of the final feature profile. (Correct answer)
- To automatically fully define the sketch.
- To add mass properties to the part.
Correct answer: To serve as a reference for creating other sketch geometry, without being part of the final feature profile.
Construction geometry, which appears as dashed lines, is used for reference purposes only. It helps in creating and constraining the main sketch geometry (solid lines) but is ignored when a sketch is used to create a 3D feature like an extrude or revolve.
Question 4: A user is creating a sketch for a part. After adding all dimensions and relations, all sketch lines turn black. What does this color indicate about the sketch's state?
- The sketch is under defined and can move freely.
- The sketch is over defined with conflicting information.
- The sketch is fully defined and has no unconstrained degrees of freedom. (Correct answer)
- The sketch contains invalid geometry that needs to be repaired.
Correct answer: The sketch is fully defined and has no unconstrained degrees of freedom.
In SolidWorks' default color scheme, black sketch entities indicate that the sketch is 'Fully Defined'. This is the desired state, meaning every entity's position and size is locked by dimensions and relations, preventing accidental changes. Blue indicates 'Under Defined'.
Question 5: Which of the following relations requires three selections to apply: two sketch entities and a centerline?
- Equal
- Parallel
- Symmetric (Correct answer)
- Collinear
Correct answer: Symmetric
The 'Symmetric' relation requires selecting two entities (like points or lines) and a centerline. It makes the two entities equidistant from the centerline, creating a mirror-like relationship across it.
Question 6: You are tasked with creating a sketch of a plate with a circular hole in the center. To ensure the hole is always perfectly centered, which two entities should you relate with a 'Concentric' relation?
- The center point of the circle and the midpoint of a plate edge.
- The outer edge of the plate (if circular) and the circle for the hole. (Correct answer)
- The circle for the hole and a corner of the plate.
- A vertical edge and a horizontal edge of the plate.
Correct answer: The outer edge of the plate (if circular) and the circle for the hole.
A 'Concentric' relation forces two or more arcs or circles to share the same center point. By making the outer circular edge of the plate and the inner circle for the hole concentric, you ensure the hole is always perfectly centered, regardless of changes to their diameters.
CSWA - Certified Solidworks Associate 2D Sketching and Relations Questions and Answers
When sketching in SolidWorks, you notice that a sketch is displayed in red and yellow colors, and the status bar indicates 'Over Defined'.
What is the most likely cause?